CNC Programmer: the person who writes the machine's instructions
What CNC programmers do between a drawing and a finished part, how the role differs from operating and machining, what current postings list, and the usual route in from the shop floor.
A CNC programmer turns engineering drawings and models into the programs that run computer-controlled mills and lathes. Using CAM software, they choose the machining strategy, tools, work-holding and cutting parameters, simulate and verify the program, and then help set up and prove it out on the machine. They also feed manufacturability ideas back to engineering. Programmers typically come from hands-on CNC machining.
What a CNC Programmer does
Programming starts before any code. The programmer studies the part, decides how it will be held, which features are cut in which order, which tools to use and how fast to run them. That plan becomes toolpaths in CAM software, which then post-processes into G-code for a specific machine.
A program is not finished until it has made a good part. Programmers simulate and check programs to avoid crashes, then set up and prove them out on the machine, adjusting feeds, speeds and toolpaths when the first part shows a problem. Setup sheets and revision control matter, because the same program may run for months.
Programmers also sit between the shop and engineering. When a feature is hard to machine, they suggest drawing changes, and when inspection finds a problem they help trace it back to the process. In production shops, much of the work is making repeat jobs faster and more consistent.
- Reviewing a new part model and drawing and choosing a machining and work-holding approach.
- Building CAM toolpaths and simulating the program before it reaches the machine.
- Proving out a first article on the machine and adjusting the program after inspection.
- Writing setup sheets and keeping program revisions under control.
- Suggesting a drawing change to engineering to make a feature easier to machine.
- Investigating a quality issue from inspection and correcting the process.
O*NET lists CNC Programmer as a job title under two occupations, Model Makers, Metal and Plastic (51-4061.00) and Computer Numerically Controlled Tool Programmers (51-9162.00), not as a separate occupation of its own. This page therefore does not use O*NET's task or skill data.
What employers ask CNC Programmers to do and bring
- Postings center the job on programming CNC machines with CAM software, including complex multi-axis work.
- Programmers are expected to give design-for-manufacturability feedback to engineering, not just program what they are given.
- The role stays hands-on: employers ask programmers to set up and prove out programs and to take part in machining and inspection.
- Verification and documentation come up in the postings: simulating programs and keeping programs and setup sheets controlled.
- SpaceX's posting sets the experience bar as several years of CNC machining with a shorter period of programming on top.
- Divergent's role includes on-machine probing programs for locating and verification.
- SpaceX's NX CAM posting expects practical cutting knowledge, such as carbide tooling and feed and speed adjustment.
These points come from current job postings on the employers' own public job boards, read on the dates shown. Each general point is backed by at least two independent sources; points that rest on a single employer name that employer. They describe what employers commonly ask for, not legal requirements, and any one employer may differ.
| Employer | Posting | Read |
|---|---|---|
| Divergent | CNC Programmer | Nov 15, 2026 |
| SpaceX | CNC Programmer, NX CAM (Starlink) | Nov 15, 2026 |
| SpaceX | CNC Programmer (Starship Components) - Level 4/5 | Nov 15, 2026 |
CNC programmer vs CNC operator, machinist and manufacturing engineer
- A CNC operator loads parts, runs proven programs and checks dimensions; the programmer writes and proves those programs.
- A machinist sets up and runs machines and may edit programs at the control; programmers do much of their work in CAM software before the job reaches the machine.
- A manufacturing engineer designs the overall process and equipment; the programmer owns the machining program for specific parts.
- In smaller shops one person often does all of these; in larger ones programming is a separate role.
How to become a CNC Programmer
- Start on the machines. Programmers usually spend years as CNC operators or machinists first; the postings we read expect machining experience.
- Learn to read drawings well. Engineering drawings, tolerances and GD&T are the input to every program.
- Learn a CAM package. Siemens NX, Mastercam and similar tools are where programming happens; the postings we read name NX.
- Learn the machine side. G-code, controls, tooling, work-holding and feeds and speeds make the difference between a program that runs and one that makes good parts.
- Ask to program simple parts. Many shops let experienced machinists take on programming gradually before the title changes.
Skills and tools CNC programmers use
- CAM software: building and post-processing toolpaths for mills, lathes and multi-axis machines.
- Simulation and verification: checking programs for collisions and errors before cutting metal.
- Drawing interpretation: tolerances, GD&T and inspection requirements.
- Tooling and cutting knowledge: tool selection, feeds, speeds and tool life.
- Work-holding: fixtures and setups that hold the part accurately and repeatably.
- Documentation: setup sheets and program revision control.
Credentials: what exists and what employers rely on
- CNC programming is not a licensed occupation, and the postings we read do not ask for a specific certification.
- Employers rely on machining experience and demonstrated CAM skills; community college and technical school machining programs are a common starting point.
Certifications are optional unless an employer or regulator says otherwise; read the posting, and check eligibility on the issuer's own site before you apply.
Where this role leads
- Machinist: the hands-on machining career many programmers come from.
- Manufacturing Engineer: if you want to design whole manufacturing processes.
- Mechanical Engineer: for designing the parts rather than making them.
- Industrial Engineer: for improving production systems and flow.
What CNC Programmers earn
TryHired does not print a salary for cnc programmers. The U.S. Bureau of Labor Statistics publishes pay for occupations, not job titles, and no BLS occupation matches this title closely enough for us to quote its pay here.
Pay for this title depends on employer, industry, region and level, so ask how the role is graded and compare offers against the posting's own range where one is published.
Applying for CNC Programmer jobs
- List the CAM software, machines and controls you have programmed or run, by name.
- Describe the hardest part you have programmed: the features, tolerances and how you held it.
- Show you prove out your own work: a first article you set up, measured and corrected.
- Mention any cycle-time, scrap or setup-time improvements you made, in numbers you can support.
Two free tools start from this job title, so you only add your own experience: draft a resume summary for a CNC Programmer role or write a LinkedIn headline for a CNC Programmer role. Neither fills in skills or results for you: list only the work you have actually done.
Disclosure: TryHired makes HIRED, a paid job-search program, so we have a conflict of interest when we mention it. Everything on this page is free to use without buying anything.
Other job titles in this group
Questions people ask
What does a CNC programmer do?
How do you become a CNC programmer?
Is CNC programming the same as machining?
What software do CNC programmers use?
How this page is built
The employer section summarises current postings from the employers' own public job boards, saved on the read date shown; every general point is backed by at least two independent sources and single-employer points name the employer; each maps to short verbatim quotes in this page's claims ledger. Employers' preferences are not legal requirements. The job, difference, path, tools and hiring sections are TryHired's explanation and advice, labelled as such. TryHired does not print pay for job titles that BLS does not publish separately.
- Pay for this title: BLS publishes occupations, not titles.
- Whether a particular employer requires a degree, a certification or a license for this title.
- How a specific company levels or names this role.
- SpaceX, “CNC Programmer (Starship Components) - Level 4/5” job posting, read Nov 15, 2026.
- SpaceX, “CNC Programmer, NX CAM (Starlink)” job posting, read Nov 15, 2026.
- Divergent, “CNC Programmer” job posting, read Nov 15, 2026.
- U.S. Bureau of Labor Statistics publishes pay by occupation; no occupation matches this title closely enough to quote.